Hotchkis 80390 TVS System, Stage 1, 67-72 C-10 Small Block, Manuel d'utilisateur

IMPORTANT NOTICE BallJointInfo:Before you install this product, please verify which front spindles you have. We have designed t

Reinstallthespring,positioningthetopofthecoilfirst.TheHotchkisa‐armincludesamodularspacerandspringisolator.Thespacer allows

67-72 C-10 Truck Front Shocks _____________________________________________________________________________8633 Sorensen Ave. Santa Fe Springs CA

1 Remove the Stock Steering Center Link SincetheHotchkisarms alterthesuspensiongeometrytoimprovefrontendgrip,thesteeringcenterli

Once you’ve removed the center link from the vehicle, compare it to the Hotchkis center link forproperorientation. SPECIALNOT

Check out our other great products for your C10 Pickup at Hotchkis.net - 19390 Sport Coil Springs (4/6 Drop) - 11390U Tubular Upper A-Arms (Impro

Hotchkis Performance LLC Return Policy & Limited Warranty Effective December 1, 2010 all Hotchkis products must be registered to qualify

OF USE OF THE VEHICLE, DAMAGE TO THE VEHICLE OR COMPONENTS OF THE VEHICLE, ANY OTHER TYPE OF CONSEQUENTIAL DAMAGES, OR OTHER INCIDENTAL OR INDIRECT

IMPORTANT NOTICE BallJointInfo:Before you install this product, please verify which front spindles you have. We have designed t

ThankyouforyourpurchasefromournewlineofChevyparts.Pleasecallusat877‐4NO‐ROLLifyouhaveanyquestionsregardingtheservic

2 Remove Front Wheels Removethefrontwheelsfromthevehicle. 3 Disconnect the Upper Ball Joint Remove the cotter pin from the upper

Oncetheballjointisloosefromthespindle,supportthelowercontrolarmwithafloorjackandraisethesuspensionslightlytorelievethe

Note:Cutangleshouldmatchsteeringstopnubangle • 73‐87OEMDropSpindle

Atthispoint,theonlythingholdingtheuppera‐armtothecaristhecrossshaft.Undothe2nutsforeacharmthatsecurethecrossshafttot

Please also note the orientation of the cross shaft.The a‐armsaredesigned to have the inner pivotlowerthanthestocklocati

Installthecrossshaftontothevehiclefirst,usingthesamenutsthatheldinthestockarms.Next,inserttheballjointstudintothespind

- 11390U Tubular Upper A-Arms (Improved Camber Curve) - 11390L Tubular Lower A-Arms (Increased Caster for Stability and Cornering Grip) - 18390 Rea

Effective December 1, 2010 all Hotchkis products must be registered to qualify for warranty at www.hotchkis.net or via the mail-in warranty card, i

PURCHASE PRICE OF THE PRODUCT. Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incide

Thank you for your purchase from our new line of Chevy parts. Please call us at 877 - 4NO - ROLL if you have any questions regarding the ser

1 Raise the Truck Raise the vehicle by using a drive-on alignment rack. Securely block the front wheels of the vehicle. 2 Remove Old Shocks

3 Support the Trailing arms Using the lifting jacks on your lift, support the rear trailing arms under the coil springs. Jack the truck up until

4 Remove Stock Shock Mounts Both the upper and lower shock mounts will be replaced. Using an air chisel, cut off the rivet heads securing the upp

• CPPModularSpindle(NOMODIFICATIONNEEDED)

Next, remove the lower shock mounts by undoing the large u-bolts holding the rear axle to the trailing arms. The lower mounts should be loose f

5 Install Hotchkis Shock Mounts Install the Hotchkis upper shock mounts as shown in the picture. Hardware is provided for mounting to the exist

Install the lower shock mounts in the same manner as stock removal. Please see picture for proper orientation and placement of side specific brack

6 Install Hotchkis/Bilstein Shocks With the mounts in place, install the shocks by starting with the lower mount. Install the following hardware i

New hardware is also provided for the upper mount. The Hotchkis upper mount has 2 adjustment holes. The hole toward the rear is the stiffer shock

1 Remove Stock Track Bar Remove the stock track bar by undoing the left frame mount bolt and the nut attaching the track bar to the rear end hous

Take the shorter adjustable bar and install it on the 2nd or 3rd hole on the driver side mount bracket. Grease bushing surface with provided lu

ThankyouforyourpurchasefromournewlineofChevyparts.Pleasecallusat877‐4NO‐ROLLifyouhaveanyquestionsregardingtheserv

Attach the passenger side frame bracket to the bar using the included hardware.

Adjust the length of the support bar so that the driver side bracket is vertical and the passenger side bracket mates to the frame rail properly.

Drill the 6 holes using a 7/16” drill bit. (Tip: Drill pilot holes with a smaller 1/8” bit first) Watch out for any fuel lines inside the frame rai

Once the holes are drilled, use the provided 3/8” hardware to mount the passenger side bracket to the frame. Fully tighten this hardware and the d

Next use the longer adjustable bar and mount it to the driver side frame bracket and the passenger side lower shock mount bracket. Choose the hole

You are finished with the Hotchkis rear suspension system!

Check out our other great products for your C10 Pickup at Hotchkis.net - 19390 Sport Coil Springs (4/6 Drop) - 11390U Tubular Upper A-Arms (Better

Return Policy & Limited Warranty Effective December 1, 2010 all Hotchkis products must be registered to qualify for warranty at www.hotchkis.n

MAXIMUM LIABILITY UNDER THIS WARRANTY SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCT. Some states do not allow limitations on how long

Thank you for your purchase from our new line of Chevy parts. Please call us at 877 - 4NO - ROLL if you have any questions regarding the se

1 Raise the Truck Raisethevehiclebyusingadrive‐onalignmentrack.Securelyblocktherearwheelsofthevehicle. 2 Disconnect the Shock

2F Remove Wheels Remove the front wheels. 3F Remove Cotter Pins Our main objective is to detach the lower control from the spindles. In order t

6F Support the lower arm and remove Nut Place a jack underneath the lower control arm and jack up to support the force from the spring. You shou

9F Install Hotchkis Coils Install the coil spring in the same manner as stock removal. Make sure to clock and index the bottom coil in the lower

1R Raising Car Raise the vehicle using a lift or floor jacks at the rear frame points. It is important that you do not jack up the truck from t

4R Install Hotchkis Rear Coils Install the coil spring in the same manner as stock removal. Your kit includes new hardware for the stock retain

Check out our other great products for your C10 Pickup at Hotchkis.net - 19390 Sport Coil Springs (4/6 Drop) - 11390U Tubular Upper A-Arms (Impro

Hotchkis Performance LLC Return Policy & Limited Warranty Effective December 1, 2010 all Hotchkis products must be registered to qualify

CONSEQUENTIAL DAMAGES, OR OTHER INCIDENTAL OR INDIRECT DAMAGES. HOTCHKIS’ MAXIMUM LIABILITY UNDER THIS WARRANTY SHALL IN NO EVENT EXCEED THE PURCH

Thank you for your purchase from our new line of Chevy parts. Please call us at 877 - 4NO - ROLL if you have any questions regarding the ser

2F Install Frame Mounts First step is to install the frame mounts. The mounts utilize existing rivet holes in the frame. You will need to air chi

3 Disconnect the Lower Ball Joint Remove the cotter pin from the lower ball joint stud.Use a wrench to loosen the castle nut th

Once the holes are clear, grab the 3/8” x 1.5” hex bolts & washers from the “front” hardware bag and insert them into the rivet holes facing

Position the mounting bracket to the frame rail and begin fastening the 3/8” bolts with the provided washers and nylock nuts. Do not tighten all t

Grab the 3/8” x 1.25” hex bolts and drop them into the mount holes on the bracket itself. Don’t forget to use washers. You can now fully tig

3F Install Bushings & Brackets Next grease the inner surface of the provided polyurethane bushings and install them onto the sway bar near to t

4F Mount Bar onto Truck Position the sway bar up to the frame mounts. Using the 3/8” hardware from the kit, start fastening the bushing brackets o

Next install additional large washers & bushings in the order shown below. Insert the bolt through the a-arm and install the smaller diamete

6F Finish Up Finish the installation by fully tightening the bushing bracket bolts. Double check all hardware for tightness and you are done with

1R Raising Car Raise rear of the vehicle by using a 4 post lift or drive-on ramps. Securely block the front wheels of the vehicle. Do not remove

5 Disconnect the Lower A-Arm Cross shaft Atthispoint,the onlythingholdingthelowera‐armtothecaristhecrossshaft.Undothe2U‐bolts

Use an air chisel to cut the head off and pop out the rivet with a punch. This hole will be your forward hole.

You will need to use the bushing bracket as a template to locate the rearward hole. Place the bracket over the rivet hole and mark the frame for t

3R Mount Sway bar on Frame

Once you have the 2 holes on each frame rail, we can install the sway bar, bushings and brackets. First, grease the inside surface of the D-shaped

4R Connect End Links Now that the bar is in place, we will attach the end links to the sway bar. Using bag#17118-2 hardware and included misalig

With the end links attached to the sway bar, adjust the length of the end links so that the sway bar lever arms are near level when the lower rod e

6R Weld Support Gusset Use hardware bag#17118-3 and mount the support gusset as shown in the picture. Grind away any rust, paint or dirt near th

7R Finish Mounting the End Link Use the rest of the hardware from bag#17118-3 to mount the lower end of the end link to the trailing arm as shown i

Check out our other great products for your C10 Pickup at Hotchkis.net - 19390 Sport Coil Springs (4/6 Drop)

ReinstalltheHotchkisa‐armsinthesamemannerasremoval.Thea‐armsaresidespecific,sopleasetakecautionwheninstallingthem.

- 11390U Tubular Upper A-Arms (Better Camber Curve) - 11390L Tubular Lower A-Arms (Increased Caster for Stability and Cornering Grip) - 30390 Anti-

Effective December 1, 2010 all Hotchkis products must be registered to qualify for warranty at www.hotchkis.net or via the mail-in warranty card, i

limitation of incidental or consequential damages and in such states the above limitations or exclusions may not apply. This limited warranty gives

Thank you for your purchase from our new line of Chevy parts. Please call us at 877 - 4NO - ROLL if you have any questions regarding the ser

1 Raising Car Raise rear of the vehicle by using a 4 post lift. Securely block the front wheels of the vehicle. Do not remove the rear wheels du

Use another jack to support the front ends of the trailing arms. 3 Remove Original Front Trailing Arm Mounts Unfasten the large ¾” bolts holdin

4 Install Hotchkis Trailing Arm Mounts Replace the original mounts with the Hotchkis Mounts. Mounting hardware is provided to replace the rivets

5 Reinstall the Trailing Arms The Hotchkis trailing arm brackets have 4 holes to choose from. The lowest hole is the same as the original. As yo

5 Optional Pinion Shim We also include an optional shim in case you would like to change your pinion angle. The shim will change your pinion angl

Return Policy & Limited Warranty Effective December 1, 2010 all Hotchkis products must be registered to qualify for warranty at www.hotchkis.n

Please also note the orientation of the cross shaft.The front section of the cross shaft has apositioningholethatmatestothe

MAXIMUM LIABILITY UNDER THIS WARRANTY SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCT. Some states do not allow limitations on how long

67-72 C-10 Truck Front Shocks _____________________________________________________________________________8633 Sorensen Ave. Santa Fe Springs CA

67-72 C-10 Truck Front Shocks _____________________________________________________________________________8633 Sorensen Ave. Santa Fe Springs CA

67-72 C-10 Truck Front Shocks _____________________________________________________________________________8633 Sorensen Ave. Santa Fe Springs CA

67-72 C-10 Truck Front Shocks _____________________________________________________________________________8633 Sorensen Ave. Santa Fe Springs CA

67-72 C-10 Truck Front Shocks _____________________________________________________________________________8633 Sorensen Ave. Santa Fe Springs CA

67-72 C-10 Truck Front Shocks _____________________________________________________________________________8633 Sorensen Ave. Santa Fe Springs CA

67-72 C-10 Truck Front Shocks _____________________________________________________________________________8633 Sorensen Ave. Santa Fe Springs CA

67-72 C-10 Truck Front Shocks _____________________________________________________________________________8633 Sorensen Ave. Santa Fe Springs CA

67-72 C-10 Truck Front Shocks _____________________________________________________________________________8633 Sorensen Ave. Santa Fe Springs CA